Toothed Ring Pommel Hawkbill Cowboy Knife in Rasp Steel, Teal Resin

Toothed Ring Pommel Hawkbill Knife in Rasp Steel with Teal Resin Handle

Our custom handmade hawkbill cowboy knife carries the original rasp crosshatch across the blade and continues that same texture straight through the ring pommel, rather than polishing the ring smooth the way most reforged knives do.

Most ring pommels are finished bright to contrast against a textured blade. Here the two match, so the knife reads as one continuous piece of reclaimed steel rather than a blade with hardware bolted to the end. A teal, black and white marbled resin handle sits between the two, pinned with brass, and the knife ships in a tooled cross draw leather sheath. The overall length is 7 inches, with a 3-inch hooked blade and a 4-inch handle.

Knife Specifications

Why Texture the Ring Instead of Polishing It?

A polished ring photographs well but tells you nothing about what the steel used to be. Leaving the crosshatch running through it keeps that story visible on every surface of the knife, not just the blade.

There is a practical side too. Texture under the finger inside the ring resists slipping in exactly the situation the ring exists to handle: a wet or gloved hand under load. A smooth ring depends on a tight fit alone.

How Is the Ring Made?

The ring is cut from the same tang as the blade, not fitted afterwards, so there is no join anywhere that can loosen over time. The crosshatch is worked into the ring by hand at the same stage as the blade, rather than added as a separate step.

Balance shifts rearward with the extra steel behind the hand, settling the knife back into the palm instead of letting the tip pull forward.

Why Does Rasp Steel Make a Good Blade?

Farrier's rasps begin as high carbon tool steel because they must cut hoof horn day after day without going soft. Reforged and taken to 60 HRC, that stock sharpens keenly and holds its edge through long work.

The crosshatch does real work beyond decoration. It sits under the thumb when you choke up on the blade, adding traction where control matters most. Similar profiles run through our cowboy knives range.

How Does a Hawkbill Cut?

Because the edge falls away from the handle, the curve draws material inward instead of pushing it forward. Rope under tension, baling twine and cordage all give way sooner on a pulling stroke.

Pressure gathers around the belly of the curve, close to the knuckles where the wrist has the most authority. If you prefer a broad straight edge, compare our rasp steel bull cutter knife.

How Does the Resin Handle Feel?

Cast resin resists moisture, oil and blood without swelling, splitting or drying out, which suits a knife that gets used wet and wiped down afterwards.

The teal, black and white swirl runs continuously into the metal at both ends, so the handle reads as a deliberate colour choice against the raw steel rather than an afterthought. Brass pins run through the full tang.

The Cross Draw Leather Sheath

The leather sheath lies flat across the front of the belt at an angle and is drawn with the opposite hand. Nothing digs into the hip when you sit, ride or lean forward.

Belt slots are cut straight through the leather body rather than stitched on as a loop. The ring sits proud above the sheath mouth, so the knife is quick to find without looking down.

Can the Knife Be Custom Engraved?

Personalised engraving is available. Enter your text in the engraving instructions field before adding to cart and our makers will apply it by hand.

The ricasso is the only fully smooth surface on this knife, so engraving sits there rather than on the textured ring or the resin. For longer requests or artwork, contact us and we will confirm placement first. Engraved knives are made to order, so allow extra production time.

How Should the Knife Be Looked After?

Dry the blade after every use and wipe on a light coat of oil before storage. High carbon steel marks quickly when damp, and the crosshatch holds water in its valleys along the blade and ring, so dry both thoroughly rather than just the flats.

Wipe the resin clean with a damp cloth as needed. Condition the leather once or twice a year and store the knife outside the sheath for long spells.

Frequently Asked Questions (FAQ)

How big is this hawkbill knife?

The blade is about 3 inches, the handle about 4 inches, and the knife measures 7 inches from tip to ring. It weighs about 195 g.

What is the blade made of?

The blade is reforged from a farrier's rasp, a high carbon tool steel, hardened to 60 HRC.

What is the handle made of?

The handle is cast resin in a teal, black and white marble swirl, pinned with brass through the full tang.

Does it come with a sheath?

Yes. Every knife comes with a basket weave tooled cross draw leather sheath.

What is a hawkbill knife used for?

The hooked blade pulls material toward you, which makes it ideal for cutting rope, twine and cordage, as well as ranch and farm chores.

Why Choose Our Toothed Ring Pommel Hawkbill Knife?

Our hawkbill brings reforged farrier's rasp at 60 HRC together with a continuous crosshatch texture across blade and ring, a teal marbled resin handle and a tooled cross draw sheath in a 7-inch package. It suits ranch work, wet weather cutting and collectors drawn to reclaimed tool steel finished as one piece.

Its teal marble resin handle and toothed ring pommel give this hawkbill knife a bold, one-of-a-kind look — a striking gift for collectors who want something different from a traditional handle finish.